Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Kitchen Remodeling: The Houston Owner’s Guide
Boral kitchen remodeling in Houston typically runs $14,000 to $45,000 for a full project, and when a Boral cabinet door, drawer front, or panel has failed, we can often match the replacement part and have it installed within a week, not a month. Most Houston homeowners reach out to us after a hinge has pulled loose from the cabinet box, a drawer glide has bent, or a door face has warped from the humidity swings our climate throws at kitchens every spring and fall. The good news: Boral’s sizing is consistent enough that matching a part is usually straightforward once we see the cabinet box and measure the door or drawer. The honest part: not every Boral line is still in production, which is why we carry matching stock and do color-and-profile matching before we ever quote a number.
We’re Elmstead Remodeling Houston, an independent contractor, not a Boral dealer or affiliate. Our crews work on Boral cabinetry in kitchens from Meyerland to Cypress to The Woodlands, and we stock common Boral-compatible hinges, glides, and touch-up kits on our trucks. If the part isn’t on the truck, our suppliers in Houston can usually have it in our hands within three to four business days. Call (254) 272-5240 and we’ll walk you through what you’re seeing.
Key Takeaways
- Full Boral kitchen remodeling in Houston: $14,000 – $45,000 installed.
- Single part replacements (hinges, glides, door fronts) are priced by the part and the cabinet, not by the whole kitchen.
- Boral cabinet boxes are modular, which means a failed drawer front or hinge rarely means replacing the entire run.
- We write the price down before work starts, and the 365-Day Done Right Promise covers every part we install.
Which Boral Models This Applies To
Boral has produced several cabinet and trim lines over the years, and Houston homes from the 1990s through the 2010s show up with Boral cabinetry more often than people expect. The lines we see most in Houston kitchens are the Boral Classic series, the Boral Designer series, and a number of private-label Boral cabinet boxes sold through regional builders. The compatibility issue that trips people up: Boral door and drawer front profiles changed subtly between production years, and a door ordered for a 2012 box will not always sit flush on a 2008 box. The height and width are identical; the profile depth and edge detail differ by roughly 1/8 inch. That is the kind of thing you don’t catch until the door is hung, and it is why we measure the existing door, not just the opening, before we order anything.
For hinges, Boral cabinets in Houston typically use one of two mount styles: a 35mm cup hinge on frameless boxes or a wrap hinge on face-frame boxes. If you open a cabinet door and look at the hinge cup, you’ll find a manufacturer stamp on most Boral-spec units, usually Salice or Blum. Both are quality brands. We stock Salice-compatible replacements on the truck because Boral used Salice hardware on the majority of the cabinets we see, and we use Blum as an upgrade when a homeowner wants smoother close action on a high-use door. For drawer glides, the common Boral spec is a 3/4 extension side-mount glide, and we upgrade to full-extension soft-close when the budget allows. Aftermarket parts are fine for Boral cabinets, but the mounting hole pattern has to match, and that’s another reason we measure before ordering.
As the owner of Elmstead Remodeling Houston, I’ve learned over years of Boral work here that the fastest way to waste a homeowner’s money is to guess at a part number. Graham Stein is my name, and the rule on every Boral job is simple: measure the part, photograph the stamp, and confirm the production year if we can. Then we quote. Not before.
Styles & brands we work with
Signs Your Boral Kitchen Remodeling Is Failing
- Sagging or dragging drawers. A worn Boral drawer glide causes friction that makes the drawer pull unevenly and eventually jam. The glide is almost always the culprit, not the drawer box itself.
- Cabinet doors that won’t stay closed or sit uneven. Boral hinges have internal springs that weaken over time, especially in Houston humidity. The door may look warped when in fact the hinge is just tired.
- Swollen or bubbled door edges near the sink or dishwasher. Steam and splash damage hit the lower cabinets first. Boral doors with exposed edges absorb moisture when the edge banding lifts, and that is a repair as much as a replacement.
- Loose or stripped hinge screws. Houston’s temperature swings cause cabinet boxes to expand and contract, and over time the screw holes in the particleboard box can strip. The door stays on, but it wobbles and eventually drops.
- Discolored or cracked laminate on the door face. Not a functional failure, but it is what throws off a kitchen remodel budget. Matching a single Boral door face is doable when the line is still in production; full refinishing is the fallback.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Houston, a full Boral kitchen remodeling project runs $14,000 to $45,000 depending on cabinetry scope, countertops, and the amount of layout work involved. A smaller Boral kitchen refresh, where we keep the cabinet boxes and replace doors, drawer fronts, hinges, and glides, typically lands between $9,000 and $20,000. Single-part work is much lighter: a Boral hinge replacement runs $85 to $250 per door including the part and labor, a drawer glide swap is $120 to $350 per drawer, and a custom-matched Boral door front runs $250 to $650 each depending on size and profile matching.
The price we write down includes the part, the labor to install it, the cleanup, and the walkthrough. It also includes something most Houston contractors don’t put on paper: if the new part doesn’t sit right after the job, we come back under the 365-Day Done Right Promise and make it right. No change orders because a hinge hole needed re-boring. No surprise line items after the fact. The written price before work begins is the entire agreement.
For full Boral kitchen remodels, the range is driven by countertop material, whether the cabinet boxes stay or go, and how much electrical and plumbing moving happens once the old layout comes out. We use KraftMaid and Cambria and Silestone alongside Boral-compatible cabinetry when a homeowner wants a mixed-brand kitchen, and those brands’ warranties travel with the finished project. A written price and a covered floor before any work begins, that is where the trust starts.
DIY or Call Us?
Cabinet hinges and drawer glides are not high-tension parts like a garage door spring, so a careful Houston homeowner can absolutely check a Boral cabinet for a loose screw, a bent glide, or a stripped hinge mount. That diagnostic step costs nothing and helps us on the phone. The place DIY goes wrong is trying to re-bore hinge holes into Boral particleboard boxes without a jig, or forcing an aftermarket glide into a hole pattern it wasn’t drilled for. What happens next is predictable: the box chips, the door hangs crooked, and the repair costs more than the original part. If you’re not certain, call us at (254) 272-5240 before picking up a drill, and we’ll talk you through it. Dropping a door front off at our shop for matching is free.
FAQs
Boral cabinet boxes with proper edge sealing typically last 20 to 30 years in Houston homes, though the hinges and glides will usually need replacement once or twice in that span. Humidity is the biggest factor, so cabinets near a dishwasher or under an unvented sink see failure sooner. We can extend the life of the boxes by replacing seals and adjusting door gaps, and we’ll tell you honestly when it’s time to stop patching. Call (254) 272-5240 for an exact quote, and estimates are free.
Soft-close hinge springs can sometimes be re-tensioned, but in most Boral hardware the spring is a sealed unit and re-tensioning fails within a few months. We don’t patch a dying hinge; we replace it with a matching or upgraded part so you’re not calling us again next season. Repairs are worth discussing for stripped screw holes in the box, where a threaded insert can often restore the mount without replacing the cabinet side.
A typical hinge or drawer glide swap takes 30 to 45 minutes per cabinet, and we can usually handle a full kitchen of hardware in a single visit. A custom-matched Boral door front takes three to five business days to come in after we measure, then an hour to hang and adjust. The photo of the cleanup happens before we leave, every time.
Call (254) 272-5240 to schedule your free estimate, and we’ll put the written price in your hand before any work starts.
Written by Graham Stein, Owner, Elmstead Remodeling Houston at Elmstead Remodeling Houston, serving Houston and nearby areas.
