Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Oldcastle Fence Installation: The Houston Owner’s Guide
Oldcastle fence installation in Houston typically runs $3,500 to $9,000 for a complete perimeter job, and we can schedule most replacement work within a few days of your written estimate. Homeowners usually find us because a gate has started dragging, a post has leaned out of line after a storm, or a section of the run is pulling away from the house. You want the section matched to the existing line, the posts set at the right depth for Houston clay, and a price written down before we start.
We install and repair Oldcastle-compatible fence systems throughout the Houston area, from Meyerland to the Energy Corridor. Elmstead Remodeling Houston is an independent contractor and not affiliated with Oldcastle. What that means for you is a written price, drop cloths and shoe covers down before the first cut, and a photo of the cleaned-up site before the crew leaves.
Key Takeaways:
- Typical Oldcastle fence installation in Houston: $3,500 – $9,000 installed
- We match your existing Oldcastle section, post depth, and hardware rather than forcing a generic panel in
- Written price before any work starts, every time
- 365-Day Done Right Promise on the completed install
Which Oldcastle Models This Applies To
Oldcastle fencing is sold through several regional lines, and the panel profile, rail length, and post dimensions vary enough that swapping in a sheet from a different series is a real compatibility problem. The sections you have in Houston may have come from the Classic, Estate, or a builder-supplied variant run. The reliable way to identify what you have is to pull a panel tag or look for a stamped number near the bottom rail; if the tag is gone, we measure the picket width, the gap spacing, and the top profile before we order anything.
On the OEM-versus-aftermarket question: for Oldcastle specifically, factory sections are the safer match when your run is recent and the profile is still in production. For discontinued profiles, a quality aftermarket equivalent from a fence supply yard we work with in Houston is often the only practical option, and it is a fine one when the rail dimensions and picket spacing are matched precisely. We will show you the options and the price difference before we commit. The same goes for gate hardware: the hinges and latch posts Oldcastle uses are standard-bore, so a heavier-gauge aftermarket hinge is usually a better long-term buy in Houston’s wind and rain than the original.
Styles & brands we work with
Signs Your Oldcastle Fence Installation Is Failing
- Post lean after rain. Houston’s clay soil expands and contracts hard through wet-dry cycles. A post that was set shallow or without enough concrete will lean visibly within a year or two, and pulling it back straight without resetting the footing just buys you a few weeks.
- Gate drag and latch misalignment. The gate is the first part to fail because it hangs all its weight on one set of hinges and one post. If you are lifting the gate to close it, the hinge lag screws or the post itself have started to move, and realignment alone will not hold for long.
- Pickets pulling loose at the bottom rail. Houston’s humidity and hard summer sun work the fasteners loose over time. Loose pickets are an early signal that the section’s rails have begun to flex, and waiting usually means replacing the whole panel instead of the fasteners.
- White chalky residue near the ground line. This is oxidation at the post base, common in areas where sprinkler heads spray the fence line directly. The post sleeve looks fine up top, but the wall below the soil line is thinning, and that is the part holding the section against Houston wind loads.
- Sections separating from the house or corner post. If the gap between the end panel and the brick widens through the year, the terminal post is slowly rotating. The fix is a larger footing and a post reset, not another lag bolt into the wall.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
The installed price for Oldcastle fence work in Houston runs from $3,500 to $9,000 depending on the footage, the post depth, and whether we are replacing one failed section or resetting the entire run. A single gate repair or a two-panel replacement lands at the low end. A full perimeter replacement at an average Houston lot, with all posts reset to a 24 to 30-inch depth, runs toward the high end.
What drives the range is honest: the condition of the existing post footings, whether the gate hardware is worth reusing, and access to the line. Houston back fences often run behind other yards, which means all debris and old sections walk out through the house to the truck. That is part of why we put drop cloths and shoe covers down inside before any of that starts.
Every Oldcastle fence install we do includes the written price first, the exact sections and hardware named on the quote, a site cleanup photo before the crew pulls out, and the 365-Day Done Right Promise. If it is not done right after the job is complete, we make it right.
DIY or Call Us?
You can safely check a few things yourself: walk the line after a heavy rain and mark which posts have moved, note where the gate binds, and pull any vine growth off the rails. What you should not do on a Houston fence is try to reset a post in clay soil without the right auger and concrete depth, or rehang a full gate panel alone. The sections are heavier than they look, and a gate under tension can twist on you when the last hinge comes loose.
If the post has moved, the footing is the problem, and the fix means digging it out completely rather than straightening it and adding dirt. We have re-done enough “straightened” posts in Houston to know the extra labor usually costs more than a proper reset done the first time. Call (254) 272-5240 and we will put a written price in your hand before any work begins.
FAQs
An Oldcastle fence in Houston typically lasts 15 to 20 years when the posts are set at a proper depth and the sprinkler heads are not spraying the post bases directly. The panels themselves can go longer, but the post footings in Houston clay are usually the failure point. If you are replacing a section and resetting the posts at the same time, we always set them to 24 to 30 inches, which is what Houston’s soil conditions actually require.
In most cases a leaning post can be reset in a new footing rather than replaced entirely, as long as the post itself has not rotted or thinned below ground. The repair means digging the old footing out completely, recentering the post, and pouring a new concrete base. We will tell you on the first visit if the post is worth saving or if the metal has gone too thin at the soil line. Call (254) 272-5240 and we will walk the line with you.
A single section or gate repair is usually done in one day. A full fence replacement in Houston takes two to four working days depending on the footage and how many old posts have to be cut out and hauled. We will give you the schedule in writing before any work starts, and quiet tools go first when there are kids napping or dogs at home.
We do not warehouse every Oldcastle profile, but we stock the most common Houston section sizes and hardware on the truck, and our fence supply partners in the Houston area can source specific profiles quickly. We also keep compatible gate hinges, latches, and heavy-gauge post brackets on hand, so a simple gate failure is often resolved on the first visit. For an exact match, call (254) 272-5240 and we will confirm the profile before we arrive.
Written by Graham Stein, Owner, Elmstead Remodeling Houston at Elmstead Remodeling Houston, serving Houston and nearby areas.
